Maker Station: Das Portable Reconfigurable Work Station für alle Makers

28 Schritt:Schritt 1: Wie es funktioniert Schritt 2: Werkzeuge und Materialien Schritt 3: Design- Schritt 4: Schneiden Sie die Teile Schritt 5: Erstellen der 2X4 Rahmen: Cutting Hälfte Lap Joints Schritt 6: Erstellen der 2X4 Rahmen: Montage Schritt 7: Anbringen unten nach 2 von 4 Rahmen Schritt 8: Anbringen des Zentrum Table Top auf die 2 von 4 Rahmen Schritt 9: Anbringen der Tabelle Leaves Schritt 10: Hinzufügen von Querstreben und Tabelle Blatt Supports Schritt 11: Erstellen der Geräterückseite Schritt 12: Befestigen der Rückseite Schritt 13: Erstellen des Frontpanels Schritt 14: Aufstecken des Bedienteils Schritt 15: Hinzufügen der Beinstützen Schritt 16: Hinzufügen der Räder Schritt 17: Aufbau der Licht Schritt 18: Installieren des Licht Schritt 19: Veredelung: Stecken Sie die Schraubenlöcher Schritt 20: Vollenden: Die Anwendung Stain und Leinöl Schritt 21: Der letzte Schliff Schritt 22: Erstellen der Werkzeug-Racks Schritt 23: Laden Sie es voller Werkzeuge Schritt 24: Optional Specialized Table Top # 1 der Werkstückhalter Schritt 25: Optional Specialized Table Top # 2: Der Juwelier Schritt 26: Fertig Schritt 27: Bonus! Schritt 28: Bonus # 2!

Maker Station: Das Portable Reconfigurable Work Station für alle Makers

Maker Station: Das Portable Reconfigurable Work Station für alle Makers

Maker Station: Das Portable Reconfigurable Work Station für alle Makers

Maker Station: Das Portable Reconfigurable Work Station für alle Makers

Maker Station: Das Portable Reconfigurable Work Station für alle Makers

Maker Station: Das Portable Reconfigurable Work Station für alle Makers

Als ich anfing, dieses Projekt wollte ich eine Arbeitsstation, die ich für eine Vielzahl von Projekten nutzen könnten und dass ich mit mir nehmen, wenn ich Demonstrationen zu bauen. Ich wollte auch etwas, das nicht dünn sein würde und etwas mit viel Nutzen in Bezug auf die Nutzflächen und Speicheroptionen. Nach vielen Skizzen, Forschung, das Spiel mit 3D-Modellen, und die gute alte Versuch und Irrtum kam ich mit dem Maker Station, eine rekonfigurierbare, zusammenklappbare, tragbare Arbeitsstation, die alles hat man sich wünschen kann, wenn Ihr bereit, gesetzt nach unten und etwas awesome.

In diesem Instructable werde ich dir beibringen, wie man einen Hersteller Station der eigenen zu bauen, werde ich die verschiedenen Werkzeuge und Materialien, die Sie benötigen, zu decken, werde ich die Konzepte und Designs, die das Endprodukt beeinflusst zu diskutieren, und dann werde ich gehen Sie durch den Build-Prozess, so dass Sie alle erforderlichen Informationen, um dieses Projekt erfolgreich zu bewältigen haben. Auf dem Weg dorthin werde ich Tipps und Tricks, die ich während des build gelernt zu teilen, so dass Sie hoffentlich vermeiden, einige der Hindernisse in Angriff genommen, während ich baue meine Maker Bahnhof.

Merkmale der Maker Bahnhof 30 "X 31" Arbeitsfläche.
-Interchangeable Tisch in der Mitte Abschnitte, die die jeweilige Aufgabe angepasst werden kann.
Built in Boden, der dem Maker Bahnhof angebracht, so das Körpergewicht hält die Station fest an seinem Platz, während Sie arbeiten wird.
-33 "Hohe Arbeitsfläche, die eine große Arbeitshöhe sowohl für stehende und sitzende Aufgaben.
-Interne Stauraum für Werkzeug und Material.
-Custom Werkzeuglagerregale, die auf der Seite der heraus Maker-Station für einfachen Zugriff auf Ihre Tools auf der Innenseite für einfache Lagerung und Transport befestigt werden kann, und.
-Die Maker Bahnhof bricht in ein 30 "x 33" x 12 "Rechteck für einfache Lagerung und Transport, (klein genug, um in den Kofferraum der meisten Standard-Größe Autos passen.)
Built in Räder für einfachen Transport.
Errichtet im zusammenklappbaren superhellen LED-Arbeitslicht.
-6 Outlet Power Strip.
-Aus Strapazierfähig Ahorn Sperrholz für Stärke und Haltbarkeit.
-Total Gewicht ist ein robustes £ 80,5 (36.5kg.)

Schritt 1: Wie es funktioniert

  1. Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Alle 8 Artikel anzeigen
    Bevor wir in die Schrauben und Muttern der Herstellung der Maker Bahnhof zu bekommen, dachte ich, es würde sich lohnen, ein paar Bilder von der Maschine entfernt von der tragbaren (geschlossen) in die Version bereit (offen) Version arbeiten umkonfiguriert hinzuzufügen. Das gesamte Setup-Prozess von geschlossen nach offen dauert weniger als eine Minute, so dass, wenn Sie bereit sind, die Maker-Station arbeiten kann schnell implementiert werden können.

    Die Schritte von geschlossen nach offen
      Klappen Sie die Vorder- und Rückseite Falten Sie die Rückwand unterhalb der Maker Bahnhof Klappen Sie den Marker-Station über auf den Boden Klappen Sie die Tabellenblätter und sperre sie ins Ort Klappen Sie die Beinstützen Klappen Sie das Licht aus und verwenden Sie die Handschraube, um ihn zu befestigen beheben die Werkzeuggestelle und fügen Sie einen Stuhl. machen etwas awesome.

Schritt 2: Werkzeuge und Materialien

  1. Maker Station: Das Portable Reconfigurable Work Station für alle Makers
    Die Materialliste für dieses Projekt ist ein bisschen lang, zum Glück gibt es keine speziellen, seltenen oder ungewöhnlichen Teile muss so sollten Sie in der Lage, alles, was bei Ihrem örtlichen Baumarkt oder im Internet zu finden sein. In Bezug auf die Kosten wird dieses Projekt wohl laufen Sie rechts um 150 bis 170 US-Dollar je nachdem, welche Materialien Sie zur Hand haben, und die Qualität der Materialien, die Sie verwenden möchten. Nachfolgend finden Sie die komplette Liste der Materialien, die ich für dieses Projekt sowie die ungefähre Preise und Links zu den Orten, wo die Materialien gekauft verwendet.
    Materialien

    Qty Materialbeschreibung Stückpreis Gesamt
    Holz
    1 ¾ "Plywood (4 'x 8' Sheet) € 53 € 53
    1 ½ "Plywood (2 'X 2' Sheet) 7,50 € 7,50 €
    3 2 "x 4" (8 Meter lang) 2,50 € 7,50 €
    Hardware
    4 3 "Rollenband 3 € € 12
    8 2 "Rollenband (in Packungen mit 2 erhältlich) 2 € € 16
    2 ¾ "Cabinet Hinge 3 € 6 €
    1 Kabinett-Handgriff 1 € 1 €
    4 3 "Gummirollen 3 € € 12
    2 Frühling Schnellspanner (in Packungen mit 2 erhältlich) 3 € 6 €
    1 Deckelstütze 6 € 6 €
    Befestigungsteile
    1 # 8 - 1 ¼ "Holzschrauben (Box of 50) 6 € 6 €
    1 # 8-2 "Holzschrauben (Box of 50) 6 € 6 €
    8 ¼ "X ¾" Halsschrauben 0,15 € 1,20 €
    8 ¼ "X 2" Halsschrauben 0,20 € 1,60 €
    8 ¼ "X 1" Fender Unterlegscheiben 0,10 € 0,80 €
    1 1/4 "-20 4 Prong T-Mutter 2 € 2 €
    1 ¼ "X 2" Bolzen 1 € 1 €
    1 ¼ "Plastic Screw Handle 3 € 3 €
    1 Screw On D-Ring Bild Kleiderbügel (4 pro Packung) 3 € 3 €
    1 Medium schraubhaken (10 pro Packung) 3 € 3 €
    Andere
    1 13 "Low Profile unter Kabinett-Licht € 24 € 24
    1 Klettband 8 € 8 €
    1 Normale Velcro 4 € 4 €
    1 6 Outlet Surge Protector € 10 € 10
    1 1 Eimer-Werkzeug Organizer 7 € 7 €
    1 Holzleim 3 € 3 €
    1 Abdeckband 2 € 2 €
    1 Wood Finish (Leinöl) 8 € 8 €
    Gesamt 220,60 €
    * Hinweis: Obwohl die Gesamt ist 220,60 €, werden Sie wahrscheinlich bereits über einige der Materialien muss für das Projekt, Dinge wie Klebeband, Steckdosenleisten, Holzleim und verschiedene Verbindungselemente, so der realistischen Preis dieses Projektes ist gleich um € 150 bis 170 €.
    * Hinweis: In Schritt 24 und 25 biete ich einige Vorschläge, wie Sie für dedizierte Aufgaben wie Schmuck machen und hält Materialien richten Sie den Mittelteil des Tisches. Diese Setups erfordern zusätzliche Materialien, die nicht in der obigen Liste enthalten sind.
    Zwar gibt es durchaus ein paar Materialien für dieses Projekt erforderlich, die Werkzeuge, die Sie benötigen, sind ziemlich Standard und gibt Dinge, die Sie wahrscheinlich schon, wenn Sie die Art von Person, Holzbearbeitungs erfreut sind. Nachfolgend finden Sie eine Liste mit allen Tools, finde ich verwendet, um die Maker Bahnhof zu bauen.

    Tools

    Tischsäge
    Dado Blade Set
    Bohrmaschine
    Phillips Schraubendrehereinsatzes
    1/4 "Forstner Bit
    1/4 "Plug Cutter
    1 "Forstner Bit
    Senken Bohrer
    Oberfräse
    1/4 "Straight / Plunge Router Bit
    Stemmeisen
    Flush Cut Hand Saw
    12 "Schellen
    Power Sander / Sand Papier
    Maßband
    Kombinationswinkel
    Tuch für Anwendung Fertig

Schritt 3: Design-

  1. Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Design war definitiv der schwierigste Teil des Projekts. Wie in Schritt 1 angegeben ist, wollte ich eine mobile Arbeitsstation, die für eine Vielzahl von unterschiedlichen Aufgaben und und nützlich für eine Vielzahl von verschiedenen Handwerker / Entscheidungsträger werden könnte, so dass es sehr viel Rücksicht wie die Höhe legen wollen des Arbeitsplatzes und die Fähigkeit, in der Tabelle wechseln sich im mittleren Bereich, so dass der Arbeitsbereich kann auf die Bedürfnisse der Hersteller und den Job bei der Hand angepasst werden. Ich verbrachte auch ein gutes Stück Zeit auf Überlegungen, wie, wie Beleuchtung, die wir alle wissen, ist eines der wichtigsten Teile eines guten Arbeitsraum zu integrieren, (kann man nicht machen, wenn Sie nicht sehen, was Sie machen oder?) Schließlich, sobald ich herausgefunden, wie alle notwendigen Attribute zu übernehmen, und wie man es anpassbare Ich hatte die Aufgabe, die es in ein schönes ordentliches Paket zusammenbrechen, so dass es wäre leicht zu transportieren, ob Sie sich bewegen zu machen es rund um das Haus oder Laden in einem Auto auf einem Kunstfestival oder Demonstration zu nehmen.

    Um durch die Design-Fragen besonders erwähnt sind, sowie einige andere, wie, wie die Vorder- und Rückseite würde falten und kommen, um den Boden zu erstellen, so dass Sie Ihr Körpergewicht wird die Tabelle fest in Position zu halten zu arbeiten, habe ich eine Reihe von Zeichnungen und Kritzeleien die ich dann verwandelte sich in 3D-Modelle via Google Sketchup. Erstellen von Modellen des Herstellers Station war sehr vorteilhaft, da es mir erlaubt, meine fertige Produkt zu sehen und verschiedene Einstellungen vornehmen, bevor ich überhaupt angefangen Bauen der Sache. Durch die Schaffung der Modelle konnte ich Ärger zu schießen Fehler, bevor sie gemacht wurden, so dass ich keine Zeit und Materialien unnötig. Als zusätzlichen Bonus Ich baute die Modelle maßstabsgetreu was bedeutet, dass ich in der Lage, alle meine Teil-Messungen direkt von ihnen zu ziehen.

    Schauen Sie sich die Google Sketch Up Modell hier:
    SketchUp: Maker Bahnhof

    Als zusätzlichen Bonus, einmal hatte ich die fertigen Modelle war ich dann in der Lage, um die Teile in der Weise, dass die gesamte maker Station könnte aus einem einzigen Blatt 3/4 "Sperrholz drei 2 von 4 ist nur sehr wenig Schrott geschnitten werden und ordnen Material, besuche die Teile Diagramme im nächsten Schritt.

Schritt 4: Schneiden Sie die Teile

  1. Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Materialien: 4 'x 8' Blatt 3/4 "Sperrholz
    Drei 8 'lang 2x4
    Der erste Schritt beim Aufbau der Maschine entfernt ist, um die verschiedenen Teile aus dem 3/4 "Sperrholz und 2X4 schneiden. Im Bild oben sind Diagramme der verschiedenen Teile, die schneiden müssen und ihre Messungen, das sind die gleichen Diagramme ich bei der Erstellung meines Maker Station, und ich bin froh zu berichten, dass alle Teile ausgerichtet und gut geklappt. (I enthalten eine metrische Version der Stückliste für alle Sie Glück Menschen gibt, die nicht wachsen wollte mit kaiserlichen Messsystem).

    Tipp: Wenn Sie wie ich sind und nicht eine groß genug, um eine vollständige 4 'x 8' Sperrholzplatte Angst nicht schleppen Fahrzeug haben. Ich entwarf die Sperrholzteile Layout, so dass Sie die Sperrholzplatte geschnitten in vier Abschnitte an der Hardware / Baumarkt ohne Beschädigung eines der Teile haben. Sehen Sie das Bild oben für ein Beispiel, wie das Blatt nach unten für den einfachen Transport gebrochen werden.

Schritt 5: Erstellen der 2X4 Rahmen: Cutting Hälfte Lap Joints

  1. Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Materialien: Vier 33 "2X4 Beine
    Zwei 30 "2X4 Querträger

    Mit schneiden alle Teile, ist der erste Schritt für den Bau der Maschine entfernt, um den Rahmen 2X4, dass alle anderen Teile zu befestigen, zu schaffen. Beginnen Sie mit dem Schneiden einer halben Überlappung in ein Ende von jedem der Beine und in beide Enden der Querträger, wie in der Abbildung dargestellt. Um diese Schnitte zu machen, installieren Sie eine dado Klinge in Ihre Tischkreissäge gesetzt und stellen Sie Ihre Schaufelhöhe so, dass es genau die Hälfte der Dicke eines 2X4 (etwa 3/4 ", weil ein 2 X 4 ist eigentlich 1,5 Zoll dick). Weitere Ihre Parallelanschlag so der Abstand von der Außenkante der dado an den Zaun gesetzt ist genau gleich der Breite eines 2X4, (ungefähr 3,5 "). Mit Set alles, nutzen Sie Ihre Gehrungslehre die Bretter über dem Sägeblatt passieren, während eines Ende gegen den Zaun gestoßen, wird dies die Rückseite Ihrer Halbüberlappungsverbindung herzustellen. Nachdem die Rückseite des Halbüberlappungsverbindung erstellt wird, weiter ausgeführt werden die Bretter hin und her über die dado gesetzt, bis Sie jede der Halbüberlappungsverbindungen erstellt haben.

    Sobald alle Halbüberlappungsverbindungen geschnitten worden ist der nächste Schritt, um die Beine und Querträger miteinander zu verbinden, um die Vorder- und Rückseite des Maker Bahnhof Rahmen zu machen. Konsultieren Sie die Bilder, um zu sehen, wie die Teile zusammengesetzt werden sollte, und verwenden Sie den Holzleim und 1 "Holzschrauben, um alles zu fixieren.

Schritt 6: Erstellen der 2X4 Rahmen: Montage

  1. Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Materialien: Vier 33 "2X4 Beine
    Zwei 30 "2X4 Querträger
    Holzschrauben
    Nine 4 "long 2X4 Distanzscheiben
    Mit den vorderen und hinteren Rahmenteile des Marker-Station gebaut wurde, ist der nächste Schritt, um sie zusammen zu stellen. Verwenden Sie hierzu die 4 "long 2X4 Abstandshalter, der auf Schritt 4 Das Ziel ist hier, um die Breite des Herstellers Stationsrahmen machen geschnitten wurden genau 7", so dass die 7 "Tischplatte wird perfekt auf dem Rahmen zu passen, ( Dies bedeutet, dass Sie vielleicht die Länge Ihres Abstandshalter leicht je nach Dinge wie die Dicke der 2X4 ist Sie verwenden anpassen.)

    Wie Sie die Abstandhalter zu positionieren ist wichtig, da ihre Platzierung festgelegt, wie und wo die LED-Licht und Rollen werden später installiert werden. Wenden Sie sich inklusive Bild für eine Vorstellung davon, wo die Abstandshalter platziert werden soll.

    Schließlich, wenn alles an seinem Platz, werden Sie mit den 2 "Holzschrauben, um die Abstandhalter an den beiden U-förmigen Schenkel und Querträgerstücke zu befestigen. Als ich baute meine Maker Bahnhof wollte ich nicht alle diese Schraubenköpfe zu sein sichtbar, so, bevor ich schraubte die Distanz anstelle Ich habe ein 1/4 "Forstner Bit auf Gegenbohrungen an den Stirnseiten der U-förmige Stücke, wo die Schrauben würde durchlaufen zu erstellen. Ich machte die Gegenbohrungen etwa 3/16 "tief, so dass ich später Holzpflöckchen über die Schrauben, um sie zu verbergen einfügen könnte, (check out Stufe 19 für Informationen über das Erstellen und Installieren von Holzdübeln.)

Schritt 7: Anbringen unten nach 2 von 4 Rahmen

  1. Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Materialien Maker Stationsrahmen
    3/4 "Bottom (30" x 8,5 ")
    1/4 "X 2" Holzschrauben
    1/4 "X 1" Fender Waschmaschine

    Nach dem Bau der 2x4 Rahmen des Maker Bahnhof fertig sind, ist der nächste Schritt, um den 3/4 Sperrholz Boden (30 anhängen "x 8.5). Dieser Boden sollte angebracht werden mit dem 2" lang 1/4 "Zugschraube und Kotflügel Unterlegscheiben. Da dieser Boden wird sein, was die Maker Bahnhof sitzt auf Sie sicherstellen, dass die Köpfe der Zugschrauben nicht durchhalten wollen, so verwenden Sie eine 1 "Forstner Bit zu erstellen Gegenbohrungen tief genug, um die Verzögerung Schraubenköpfe aufnehmen und Unterlegscheiben. Sobald die Gegenbohrungen erzeugt werden, Pre-Bohrungen für die Ankerschrauben so dass die Beine nicht spalten, wenn Sie schrauben sie an ihrem Platz.

    Beachten Sie, dass die Maker Bahnhof Rahmen sollte genau sein 7 "breit und dass der Boden ist 8,5" breit. Die zusätzliche mit der Boden liefert Raum für die Beinstützen, die später hinzugefügt werden, so jetzt stellen Sie sicher, dass der Boden über hängt jeder der Seiten 3/4 "(siehe Bild).

Schritt 8: Anbringen des Zentrum Table Top auf die 2 von 4 Rahmen

  1. Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Materialien Maker Bahnhof Assembly
    3/4 "Sperrholz-Center Table Top (30" x 7 ")
    3 Schnellspanner
    Anbringen der Tisch in der Mitte oben ist ein ziemlich einfacher Prozess. es wird perfekt mit der Oberseite der die Maker Bahnhof Rahmen ausgerichtet werden und wird an Ort und Stelle mit 3 Federsysteme Schnellspanner statt. Das einzige, was hier zu beachten ist, um sicherzustellen, dass Sie die Federspanner zu installieren, so dass sie nicht in der Art und Weise für die ausklappbaren LED-Licht, das später installiert wird, (ich habe das nicht als ich das erste Mal installiert die Schnellspanner und hatte, sie zu entfernen, um Platz für das Licht später machen).

Schritt 9: Anbringen der Tabelle Leaves

  1. Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Materialien Maker Bahnhof Assembly
    Zwei 3/4 "Plywood Table Leaves (30" x 12 ")
    Vier 3 "Scharniere und Schrauben zur Montage
    Einst das Zentrum Tischplatte angebracht ist der nächste Schritt, um den vorderen und hinteren Tisch Blätter zu befestigen. Beginnen Sie, indem Sie den gesamten Maker Bahnhof über so das Zentrum Tischplatte ist auf einem vollkommen ebenen Fläche sitzt, (für mich war dies die Tabelle von meinem Tisch sah, mit der Klinge aus dem Weg abgesenkt). Mit der ganzen Versammlung drehte Sie können nun auf die flache Oberfläche der Sie gerade arbeiten, um, dass die verschiedenen Bereiche Ihrer Tischplatte alle Licht perfekt sicherstellen. Jedes der Blätter wird durch zwei 3 angebracht werden "Scharniere, je nach Marke von Gelenk Sie sich entscheiden, Sie müssen möglicherweise verzapfen das Gebiet, wo die Scharniere installiert werden, so dass alles richtig öffnet und schließt, (für die Scharniere I Strahlen verwendet Ich musste ein Zapfenloch in den 2x4 Kreuz geschnitten groß genug, um eine Seite des Scharniers passen und dann einige zusätzliche Arbeit zu tun, um Platz für den Fässern der Scharniere mit einer Bucht förmigen Fräser machen hatte ich.

Schritt 10: Hinzufügen von Querstreben und Tabelle Blatt Supports

  1. Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Alle 7 Artikel anzeigen
    Materialien Maker Bahnhof Assembly
    Zwei 3/4 "Sperrholz Querstreben (26" x 3 ")
    Zwei kleine Fetzen von 3/4 "Sperrholz (mindestens 3" x 1.5 ")
    Holzschrauben
    Zwei 3/4 "Table Blatt Supports (18" x 3 ")
    Zwei 3/4 "Cabinet Scharniere
    Obwohl die Blätter nun angebracht, gibt es nichts, um sie in Position zu halten, so dass in diesem Schritt werden das Hinzufügen der Tabellenblattträger und die Querstreben, die sie angeschlossen sind.

    Dieser Prozess beginnt durch Befestigen eines Blocks von 3/4 ". Sperrholz dem Zentrum von jeder der Querstreben der Block sollte etwa 3" lang und ca. 1,5 "hoch, dieser Block sein wird, was das Blatt stützt anliegen, um die Niederhalte Tischblätter in der ausgefahrenen Stellung.

    Als nächstes wird mit der Maker Bahnhof noch nach oben auf eine ebene Fläche Maßnahme setzte sich von der Unterseite der Tischblätter 13 "und eine Markierung auf jedem der vier 2X4 Beine. Diese Markierungen sind, wo die Querträger installiert werden soll, (siehe das Bild für eine visuelle Darstellung). Verwenden Sie die Schrauben 1 ", um die Querträger zu fixieren.

    Sobald die Querstreben sind in der nächsten Stufe eingeschraubt ist, bauen die Blattstützen. die Urlaub Stützen bestehen aus Sperrholz Teil zuvor geschnitten (18 "x 3") und eine 3/4 "Möbelscharnier. Die Sperrholzblatt unterstützt einen 45-Grad-Schnitt an einem Ende und das Scharnier auf der anderen installiert. Sie werden installiert wie in der Abbildung dargestellt, (um festzustellen, wo sie installiert werden müssen drücken Sie die 45-Grad-Ende der Blatt Unterstützung fest gegen den Block, den Sie der Querstrebe angebracht und positionieren Sie das Ende mit dem Gelenk an der Unterseite der Tischplatte. Markieren Sie die Scharniermontagelöcher und schrauben Sie das Scharnier in Kraft., da die Tabelle Oberfläche des Maker Bahnhof gegen die ebene Arbeitsfläche registriert die Tabellenblätter sollte perfekt auf Höhe der Mitte des Tisches nach leaf Unterstützung Installation abgeschlossen ist.)

Schritt 11: Erstellen der Geräterückseite

  1. Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Materialien 3/4 "Sperrholz Rückseite A (30" x 23,5 ")
    3/4 "Sperrholz Rückseite B (30" x 9.5 ")
    Zwei 2 "Scharniere
    In diesem Schritt werden Sie mit Scharnieren an der Rückseite befestigen (A), um Panel (B) hinten. Das ist ein ziemlich geradlinig Prozess, so stellen Sie sicher, dass die Kanten der beiden Platten sind bündig und installieren Sie dann die Scharniere so, dass sie im gleichen Abstand von jeder Seite und so, dass sie im Laufe der Sitzung Kanten der beiden Platten zentriert sind .

Schritt 12: Befestigen der Rückseite

  1. Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Materialien 3/4 "Sperrholz Plattenbaugruppe
    Maker Bahnhof Assembly
    Zwei 2 "Scharniere
    Um die Plattenbaugruppe an den Maker Bahnhof befestigen drehen Sie die Baugruppe über, so dass die Scharniere, die Abdeckung A Abdeckung B zu verbinden sind verdeckt und dann mit zwei 2 "Scharniere, um die Montage an der Unterseite des Herstellers Station anhängen, wie dargestellt.

    Hinweis: bis zu diesem Zeitpunkt die Maker Bahnhof hat eine bestimmte vorne oder hinten, wenn angebracht die Plattenbaugruppe hatte bestimmt, was die Vorder- und Rückseite der Maschine entfernt sein, so, wenn Sie eine Seite haben, mit dem Sie die Front sein wollen aus einem bestimmten Grund sicherstellen, dass Sie nehmen, dass in Betracht, wenn Sie die Plattenbaugruppe zu befestigen.

Schritt 13: Erstellen des Frontpanels

  1. Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Materialien 3/4 "Sperrholz Front Panel (30" x 33 ")
    Alle 2 "Trim Boards
    Holzschrauben
    Holzleim
    Die Frontplatte der Maschine entfernt ist von der Frontplatte, die aus der 3/4 geschnitten wurde zusammengesetzt "Sperrholz (33" x 30 ") und alle Verkleidungsplatten, die aus der 3/4 abgeschnitten wurden" Sperrholz (2 "breit von unterschiedlicher Länge). Die Zierbretter sind ein wichtiger Teil der Frontplatte neben Hinzufügen in die Maker Bahnhof ästhetische sondern auch den Aufbau der Dicke der Frontplatte, so dass, wenn die Rückseite und Frontplatten der Station verbunden sind, um das zu machen Fußboden beide sind sit auf gleicher Höhe.

    Hinweis: Ich habe nicht die Schrauben, die Zierleisten an der Frontplatte halten sichtbar sein sollen, so dass ich zu begegnen bored die Schraubenlöcher mit einem 1/4 "Bohrer, (wie ich für die Schraubenlöcher in dem Rahmen hat ,) in Vorbereitung für Holzdübeln, die zu einem späteren Zeitpunkt eingesetzt wird.

Schritt 14: Aufstecken des Bedienteils

  1. Maker Station: Das Portable Reconfigurable Work Station für alle Makers
    Materialien Maker Stationsrahmen
    Front Panel Assembly
    Zwei 2 "Scharniere
    Die Frontplatte ist in einer ähnlichen Weise, wie die Rückplatte befestigt wurde angebracht. Drehen Sie die Frontplatte um, so dass das Verkleidungs ​​Seite nach unten zeigt und dann mit zwei 2 "Scharniere, um die Platte auf der Unterseite des Maker Bahnhof fixieren, wie in der Abbildung dargestellt.

    Beachten Sie, dass es einfacher ist, die Frontplatte zu befestigen, wenn Sie die Rückwand unterhalb der Maker Bahnhof gefaltet habe (wieder, wie in der Abbildung dargestellt.) Das Umlegen des Rückseite unter dem Maker Bahnhof wirft die Höhe der unteren der Station, so dass die die Frontplatte reiht sich perfekt in den Boden.

    Hinweis: Sobald die Vorder- und Rückseite angebracht sind wird es nichts, um sie in der geschlossenen Position zu halten, bis dann die Platten rund Flop (später, nach Abschluss, wird industrielle Stärke Velcro installiert zu erreichen halten die Platten gehalten werden geschlossen.) und möglicherweise nach unten kommen mit genügend Kraft, sie könnten zu Verletzungen führen oder reißen Sie die Scharniere halten, dass sie an ihrem Platz. Um diesem Problem abzuhelfen, Klammern verwenden, um die Vorder- und Rückseite, um die Beine des Maker Bahnhof halten. Die Klemmen wird sicher halten Sie die Paneele in dem Sie drehen und drehen Sie den Bahnhof, während Sie Dinge wie die Installation der Räder oder die LED-Licht.

Schritt 15: Hinzufügen der Beinstützen

  1. Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Materialien Maker Bahnhof
    Vier 3/4 "Sperrholz Beinstützen (Triangular 18" x 8 ")
    Eight 2 "Scharniere
    Mit den Vorder- und Rückwand befestigt ist der nächste Schritt, um die dreieckige Beinstützen befestigen. Insgesamt gibt es 4 unterstützt, eine für jedes Bein und jeder Träger wird unter Verwendung von zwei 2 "Scharniere. Anbringen der Beine ist eine ziemlich geradlinig Prozess, aber es gibt zwei Dinge, die Sie beachten müssen, bevor Sie beginnen befestigt werden.

    Zunächst erinnern, zurück zu dem Schritt, wo der Boden wurde dem Maker Station (Step 7) befestigt ist. wenn die untere angebracht wurde es 3/4 "Überhang auf jeder Seite, das Überhand werden, wo die Beinstützen zu setzen, wenn sie in der geschlossenen Position sind, ist das Problem, daß die 3/4". Beinstützen plus der Dicke der Scharniere wird zu dick sein und wird Probleme, wenn sie versuchen, alles zu falten verursachen. Die Lösung ist, die Scharniere mortise in die Beinstützen so daß die Träger bündig mit den Beinen, wenn sie gefaltet sind geschlossen; (Siehe die Bilder für Informationen über das Schneiden der Nuten und Einbau der Scharniere).

    Zweitens, wie die Beinstützen schwenken in Ort, den sie an den Scharnieren, die die Vorder- und Rückseite, um den Boden des Maker Bahnhof befestigen fangen kann, um dies zu I verlegt den Unterseiten der Schenkel zu halten unterstützt, um Freiraum bieten, so dass sie können einfach deaktivieren Sie die Scharniere. Um diesen Abstand zu Ich habe einen Router mit einer 1/2 tiefe Lücke in der Mitte der Unterseite der Beinstützen "gerade etwas, eine 1/4 schneiden". Haben auch Sie Fotos für eine visuelle Darstellung.

Schritt 16: Hinzufügen der Räder

  1. Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Materialien Maker Bahnhof
    Zwei 3/4 "Sperrholz Radträger (12" x 4 ")
    Eight 2 "Halsschrauben
    4 Lenkrollen
    Sechzehn 1 "Halsschrauben

    Beginnen Sie mit der Befestigung der Rollen an den Radträger (12 "x 4"), wie in den Abbildungen gezeigt. Beachten Sie, dass ich aufgenommen 1/2 "Sperrholz Abstandshalter an das Rad unterstützt, weil die Zugschrauben ich für die Installation der Räder gekauft waren ein wenig zu lang und würde durch die Spitze der 3/4 stocherte haben" dick Rad unterstützt. Nachdem Sie die Rollen mit dem Rad verbunden haben unterstützt, verwenden Sie die 2 "lange Holzschrauben zur Befestigung der Radträger an den Maker Bahnhof Rahmen. Wie Sie aus den Bildern die Radträger sind einige Zoll vom oberen und unteren Ende der Installation sehen, Maker Station, das war mit der Stabilität und dem Prozess der Rollen der Station off der Räder und auf den Boden zu helfen, wenn Sie bereit sind, es für die Arbeit einzurichten sind.

    Hinweis: Denken Sie daran, dass es eine spezifische Seite für die Räder und eine bestimmte Seite für das Licht, stellen Sie sicher, dass Sie die Räder befestigen an der rechten Seite, wenn Sie nicht mehr wissen, welche Seite ist, die einen Blick auf die Bilder auf Schritt zurück 1.

Schritt 17: Aufbau der Licht

  1. Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Alle 11 Artikel anzeigen
    Materialien 3/4 "Sperrholz Licht 1. Arm (3.5" x 3.5 ")
    3/4 "Sperrholz-Licht 2. Arm (26" x 3.5 ")
    3/4 "Sperrholz Licht Arm # 3 (22" x 3.5 ")
    Zwei 2 "Scharniere
    Utilitech 13 "LED unter Kabinett-Licht
    Rockler Stamm-Kappen-Unterstützung
    Macht das Licht kann ein bisschen von einer verwirrenden Prozess sein, weil Sie gehen zu werden hin und her zwischen den verschiedenen Licht Armteile Schalt, ob alles passt perfekt zusammen. Hier sind die wichtigsten Dinge, die Sie wissen müssen, bevor wir anfangen müssen.
    Das Licht wird auf licht Arm # 3 (die 22 montiert "lang). Licht Arm # 3 erhält einen flachen Kanal Schnitt in ein Ende, um das Kabel von der Lichtnehmen. Leichte 2. Arm (26" Long) wird auseinandergeschnitten und zusammengesetzt, so dass es eine rechteckig geformte Öffnung in der Mitte davon. (Dieses Loch ist, wo das Licht geht, wenn alles zusammengelegt.) Wenn Licht 2. Arm wurde zerschnitten und wieder zusammengebaut Licht Arm # 1 (3.5 ") wird an einem Ende der es aus geklebt. Okay, mit allen, dass die Art, wie hier geht es.
      Der erste Schritt beim Aufbau das Licht ist zu zerschneiden Licht am 2. Arm. Beginnen Sie mit dem Schneiden eines 1 "breiten Streifen von jeder der langen Seiten, so dass Sie zwei 1 haben" X26 breit und 26 "lang. Nun nehmen Sie das Mittelteil" lange Streifen. Diese werden Sie mit einem Mittelteil, das etwa 1,5 ist verlassen " und schneiden Sie sie auseinander, so dass Sie ein Stück, das etwa 4 ist "lang und ein weiteres Stück, das etwa 8 ist" lang. Mit diese beiden Stücke schneiden Sie hinzufügen können, was auch immer auf Ihre Schrott bin gelassen. Nun kleben Sie die vier Stücke einfach zusammen wie gemacht 2 in der Abbildung dargestellt, um Licht Arm wieder zusammenzusetzen ". kleben Licht Arm # 1 bis zum Ende des Licht 2. Arm, wo Sie die 8 verwendet "lange Mittelstück. Während die anderen Stücke trocknen, nehmen Licht Arm # 3 und schneiden Sie ein 1/4" breite Rille, die etwa 1/4 tief ist in der Mitte davon. Beachten Sie, dass diese Nut sich nicht über die gesamte Länge der Platte erstrecken; sondern es geht nur in etwa 5 bis 6 Zoll. Dies geschieht, indem Sie das Board über den Tisch Sägeblatt und stoppen, nachdem Sie etwa 5 cm in der, (Besuche die Abbildung, um zu sehen, was ich meine.) Nach einem Schnitt zurück das Board gemacht von der Klinge geschnitten getan, mehr Ihren Zaun über etwas und einen weiteren Pass, um die Breite des Zwischenraums zu erhöhen, um sicherzustellen, dass alle meine Schnitte endete an der gleichen Stelle habe ich ein Anschlagblock eingespannt, um den Zaun wieder Besuche das Bild zu sehen, was ich bedeuten. Als nächstes installieren Sie das Licht auf Licht Arm # 3, so dass es zentriert ist und damit in den offenen Bereich im Licht Arm # 2 erstellt passt. Denken Sie daran, das Licht so zu installieren, dass die Schnur ist auf der Seite mit der Nut. Now use a 2" hinge to attach the end of light arm three that is grooved to the end of light arm #2 that isn't glued to light arm #1. Tip: make sure the cord is in the groove in light arm #3 before you screw the hinge in place, otherwise you will have to remove the hinge to install the cord. Good job so far, with all the light arm pieces attached the only thing left to do is to attach the lid support to one side of the assembly. This support will be what holds the light up when it is in the open position, (kind of like the hinge that holds the legs of a step ladder apart).
    Hopefully that wasn't to hard to follow, it's actually a pretty simple process but with all that talk of light arms it can sound a bit confusing.

    With the light assembly built, the next step is to attach it to the Maker Station, continue on to step 18 to learn how to do so.

Step 18: Installing the Light

  1. Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Alle 7 Artikel anzeigen
    Materials Maker Station
    Light Assembly
    One 2" Hinge
    One Threaded Insert
    One Hand Knob Screw

    Alright, With the light built, the next step is to attach it to the Maker Station. Thankfully attaching the light is a much simpler task than building the light.

    Start by locating the side of the Maker Station where the light will be installed, you can reference the pictures on the first step to help with this. Once you've found the correct side, install a 2" hinge as shown in the picture, note that the hinge is mortised deep, similar to how the hinges were mortised on the leg supports. With one side of the hinge attached to the Maker Station, attach the other side to the light assembly as shown in the picture.

    Next, flip the light up (like how it would be if it were in use) and drill a 1/4" hole through the light assembly so that you tag the Maker Station with the tip of the drill bit, this hole will be used to installed the 4 prong T nut thread insert and hand knob screw that holds the light in place while in the up position. Note, make sure that you drill the hole high enough so that you don't come in contact with the hinge plate that holds the light assembly to the Maker Station.

    With the hole drilled, install the 4 prong T nut threaded insert, pass the hand knob screw through the light assembly and give it a few turns to lock the light into place. when you want to close the light simply unscrew the hand knob and allow the light to swing into place between the legs of the Maker Station.

    Note: After finish has been applied, double sided Velcro will be added where the light folds closed so that it doesn't inadvertently swing open. Also, a Velcro strap will to the small space left at the bottom of the cavity that the light folds into so that the light cord can be wrapped up for storage. Check it out on step 21.

    With the light installed the major construction of the Maker Station is complete, from here on out I'll be covering finishing touches, applying finish, and making accessories for the Maker Station.

Step 19: Finishing: Plugging the Screw Holes

  1. Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Tools and Materials Scrap Hard Wood
    Wood Glue
    Plug Cutter
    Flush Cutting Saw
    Sand Paper

    With the major assembly of the Maker Station complete it's time to shift focus to finishing. If you remember back to steps 6 and 13, I discussed how I counter bored the screws holes I drilled so that wooden plugs could be installed later on to cover up the screw heads. Well now it's time to talk about those plugs, how they are made, and how they are installed.

    To make the plugs you need a plug cutter that cuts plugs the same size as the diameter of the counter bores you drilled, (in this case 1/4"). Plug cutters can be bought from retailers like Sears, Amazon, Woodcraft, etc.

    Chuck the plug cutter into your drill just as you would a drill bit. Next position the plug cutter on whatever material you wish to use to make your plugs, in this case I chose to use a scrap of red paduke, an exotic hardwood with a beautiful bright red color. Start your drill and apply gentle downward pressure until the plug cutter has cut 1/8" to 3/16" into the wood.

    Next use a saw from the side to cut underneath the plug freeing it from the stock wood.

    Now do this about 60 times.

    Note : The speed and accuracy of this process can be greatly increased if you substitute a drill press for the hand drill and a band saw for the hand saw.

    Once you have all the plugs cut installing them is a simple matter of squeezing some wood glue into the counter bored holes and then inserting the plugs with a bit help from a soft faced hammer. When the glue has dried you can cut the plugs flush with a flush cut saw and then you can use sand paper to sand them smooth.

Step 20: Finishing: Applying Stain and Linseed Oil

  1. Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    With the plugs installed you're ready for the last big step of this build, applying the finish. Generally I like polyurethane finishes but for this project I decided to stick with a traditional boiled linseed oil finish. Linseed is a wonderful finish for a project like the Maker Station because it is very easy to apply, can be applied in multiple coats to build up luster, is very protective, dries hard, and is most importantly easy to repair when the inevitable mishap occurs, (The Maker Station is essentially a mobile work bench after all so you're going to ding it up at some point).

    Before applying the linseed oil finish I applied walnut oil-based stain to the work surfaces of the Maker Station and to the front trim boards, this was an aesthetic choice as I thought contrasting colors would look nice in these areas.

    As for applying the linseed finish, the process is very simple and almost fool proof which is fantastic if you're someone like me who hates finishing wood projects because of issues like drips, sags, and shiny spots. Linseed oil won't leave drips or sags because it's a penetrating oil finish that you wipe on and wipe off after a few minutes, and it creates a nice soft luster that looks very professional on all types of wood projects. To apply, simply use a cloth to thoroughly rub the linseed oil all over the project making sure to coat all surfaces, edges and corners. Allow the oil to set for 10 to 15 minutes and then wipe off any excess.

    Generally two to three coats of linseed oil will yield a nice finish, however if you're looking for a nicer finish more coats of linseed oil can be applied to build up the luster, (for my Maker Station I applied two coats to the entire station and then 2 additional coats to areas like the floor and work surface, areas where I wanted a bit of additional wear resistance.

    Tip: to make finishing easier I removed the light assembly and middle section of the work surface; I finished these components separately and then re-installed them into the Maker Station.

    Tip : After finishing the exposed edges of the plywood parts looked pretty terrible. To hide these unsightly edges I used black acrylic paint which created a very sharp finish with nice contrast.

Step 21: Finishing Touches

  1. Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Materials Adhesive Velcro
    Normal Velcro Strips
    Power Strip

    At this point the Maker Station is all but complete, with the finish applied and dry the last step is to add on the finishing touches (mainly Velcro). Apply adhesive Velcro to areas like the light assembly, the front and back panels, and basically anywhere else where there is a moving part that you don't want to be swinging all over the place, (you can reference the pictures to see where exactly I put Velcro).

    Once you've finished with the hook and loop, you can install a power strip onto the inside of the Maker Station to give your work area a few more outlets for those times when you need to run the light, a rotary tool, a soldering iron, and a panini maker all at the same time.

Step 22: Creating the Tool Racks

  1. Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Alle 7 Artikel anzeigen
    Materials Bucket Organizer
    1/2" sheet of plywood
    Screw on Picture Hangers
    Thread and Needle
    Screw in Hooks

    The tool racks are basically a bucket tool organizer that has been cut apart and reconfigured to make two flat panels with tons of pockets for storing all sorts of tools. These panels give you a lot of options in terms of what tools you bring with you and best of all they can be stored inside the Maker Station for easy transport and can then be mounted to the side of the Maker Station so that you have quick and easy access to your most useful tools.

    How to make the Tool Racks
      The bucket organizer should be build in such as way that it can easily be separated into two equal sections so use a seam ripper or good old fashioned scissors to to break it down as shown in the picture. With the bucket organizer separated you should now have two pieces, each of which should have a front flap (the part of the organizer that goes on the outside of the bucket), and a back flap (the part of the organizer that goes inside the bucket). Fold the back flaps underneath the front flaps and stitch them together to create a pocket, (note: if you don't want your seam to be visible, sow the fronts and backs together inside out and then turn the whole thing inside out once you've finished sowing to move the seams to the inside). Next cut a piece of 1/2" plywood large enough to fit inside the pocket that was created when the fronts and backs were sown together, (note: the plywood panel should fit tightly inside the pocket. With the 1/2" plywood panels inserted into the the bucket organizer pockets, install the hangers onto the backsides of these assemblies as shown in the picture. (Note: pay attention to how far apart you mount the hangers, about 8" apart should be good. With the hangers mounted your tool racks are ready to go, the only thing left to do is to mount screw hooks for the tool hangers to hang on. Mount hooks underneath the upper most wheel support as shown in the picture, and then mount hooks inside the maker station, again as shown in the picture. Mounting hooks in these areas will allow you to hang the tool racks when the Maker Station is in the closed and open positions. ( Tip : remember to mount the hooks the same distance apart as the hangers you installed on the tool racks).
    At the end of this process you will have two tool racks giving you the ability to switch out the tools you're carrying based on the task at hand.

Step 23: Load it Full of Tools

  1. Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Alright, after a good bit of work we're finally at the fun part, loading it full of tools and getting ready to put the Maker Station to work. In terms of tool storage you have a lot of options; you can store your hand tools in the tool racks that were made back on step 22, and for bigger things like power tool cases and small tool boxes there is plenty of room on the inside of the Maker Station when it is folded up, (see picture).

Step 24: Optional Specialized Table Top #1 The Work Holder

  1. Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Alle 8 Artikel anzeigen
    One of the best things about the Maker Station is it's ability to be customized based on the task at hand. This customization comes in the form of interchangeable specialized table top inserts that can be customized for tasks like wood working, jewelry making, cooking, drawing, painting, and any number of other skills or hobbies. Although there is no limit to the types and amounts of table inserts that can be made, I wanted to share with you two of my favorite and most used table inserts. On this step you'll learn about the Work Holder Insert and on step 25 you can check out the jewelry making insert.

    The Work Holder

    The work holder is a specialized table insert that utilizes hold down clamps and "T" slots to create a clamping surface for a variety of projects.

    How to make the Work Holder Table Insert

    Materials 30" X 7" 3/4" Plywood
    Hold Down Clamps
    Black Acrylic Paint

      Start by cutting a 30" X 7" rectangle from a piece of 3/4" plywood (exactly as you did to create the original center table top) Next determine what side of the table insert you want to be the top and then use your table saw to cut two 1/4" deep grooves into that side as shown in the picture. (Note these grooves are approximately 1.5" in from the edges of the table insert). The reason for cutting these grooves is to remove most of the material from the areas where you will be routing the "T" slots so that your router doesn't have to work as hard to remove the extra material. Once you have cut the grooves with your table saw, the next step is to use your router equipped with the "T" slot cutting bit to create the "T" slots. Clamp a straight edge in place to ensure that your slots end up straight and then start routing the slots. While routing take your time and back your router off every few inches to give it a break and to clear out some of the saw dust and chips that may be trapped in the slot. When you have both slots cut, use some sand paper to smooth our any rough areas created during routing. After the work holder table insert has been sanded, apply your finish of choice. (I chose a matte finish black paint.) Lastly install toggle clamp catches just as you did for the original table center so that the work holder table insert can be locked into place.

      With the work holder insert complete you can add on the hold down clamps by sliding them into the T slots and you're ready to go.

Step 25: Optional Specialized Table Top #2: The Jeweler

  1. Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    The jewelry making insert takes some of the most important tools and equipment for making jewelry and combines them into one 30" x 7" work surface.

    The jewelry making insert includes:
    -Rotary Tool Stand
    -Storage for 30 Rotary Tool Bits
    -Bench Pin
    -Contoured Sanding Surfaces
    -File Storage for 12 Needle Files

    Making the jewelry insert is a pretty straight forward process and the included pictures should give you just about all the information you need to tackle this project. Most of the structures on this table insert were built using scrap 3/4" plywood or scrap 2X4. The only tricky part of this build was making the file rack, to make it I cut 12 shallow grooves into a scrap of 3/4" plywood using my table saw; (one groove for each file.) Once the file holder part was made, I used a 3/4" thick dado set to make an angled cut into another scrap of plywood to create the base of the file rack I slotted the file holder into the base and used screws to fix the two together. Once the file rack was complete I used wood glue and clamps to fix it to the table top.

    Just like the Work Holder insert, the Jewelry insert was finished with a protective coat of black paint.

Step 26: Finished

  1. Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Thank you for taking the time to check out my Instructable on building the Maker Station. I hope you found the information presented here to be useful and interesting. If you have any questions or comments please feel free to post them in the comments section and I will do my best to get back to you as soon as possible, and I really enjoy hearing your thoughts and opinions so please don't be shy about posting!

    Also, If you enjoyed this Instructable please consider voting for me in the Portable Work Station, Wood Working, and Full Spectrum Laser Contests

    Best Regards!

Step 27: Bonus!

  1. Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    One of the unexpected benefits of the Maker Station design is the fact that the work light is stored on the top of the station when it is in the closed (portable) configuration. I noticed this and saw the potential to add a bit of utility to the Maker Station by turning it into a floor lamp via a simple fixture made from a scrap of 2x4 and a 4 prong T nut (like the one used to fix the light in place when the Maker Station is set up for work.

    To make this piece simply cut a piece of 2x4 that is roughly 4" long and while holding the light in the upright position, butt the piece of 2x4 up against the light and use a pencil to make the location of the screw hole that was drilled in the arm. With the location of the screw hole marked, install the 4 prong T nut into the piece of 2x4 just as you did when you installed the first one into the Maker Station. With the T nut installed the light modification is now complete, simply use the hand screw to screw the piece of 2x4 against the light which will hold it open for use as a floor lamp.

Step 28: Bonus #2!

  1. Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    Maker Station: Das Portable Reconfigurable Work Station für alle Makers

    You may have noticed a neat little wooden stool in some of the pictures throughout this Instructable. I designed that stool specifically to go with the Maker Station as it's design allows it to fold up small enough to fit inside the station for storage and transport. In the next few weeks I'll be publishing an Instructable all about the design and construction of the stool, until then, check out these pictures to see how it works!

    And again, Thank you all for your views and comments, all the comments I have seen so far have been very supportive and have asked really interesting and thought provoking questions!